Mercury 4.0HP & 5.0HP 2 Stroke Service Kit
Service your Mercury 4 & 5 hp two-stroke with the listed Mercury/Quicksilver parts, gear lubricant and NGK spark plugs. Choose optional extras to suit the work your engine needs.
For the single-cylinder Mercury 4 and 5 hp two-stroke family. Check the engine serial and existing pump parts; the similarly sized FourStroke engines use a different kit.
Standard inclusions
| Item | Quantity / contents | Part reference |
|---|---|---|
| Gear lubricant | 1 Ă— 946 mL High Performance gear lubricant | 858064K01 |
| Spark plug | 1 Ă— NGK BP7HS-10 | BP7HS-10 |
| Gearcase drain/vent seals | 2 | 8M0082880 |
| Impeller | 1; replaces 16154 3 | 8M0204676 |
| Water-pump gaskets | 1 of each | 8M0155369; 16160004 |
Quantities are for one engine. The 946 mL bottle is gear lubricant. Two-stroke engine oil is separate.
Choose your optional extras
Select extras beside the Add to Bag button; the price updates with your choices. The items shown below are optional unless included in the table above.
Spark plug, impeller and pump gaskets are included. Choose the liner and wear plate if they are scored or worn. The fuel valve, fuel filter, gear-lube pump and marine grease are optional.
Fuel, oil and gearcase guide
| System | Service guide |
|---|---|
| Engine lubrication | 50:1 after break-in: 100 mL of NMMA-certified TC-W3 outboard oil per 5 L of petrol. Follow the separate break-in ratio for a new or rebuilt engine. |
| Gearcase lubricant capacity | Approximately 0.195 L. |
Gearcase capacities are approximate. Use the specified filling and level-check procedure for your engine and gearcase; the size of the retail bottle is not a fill instruction. Two-stroke engines use oil in the fuel or oil-injection system, rather than a four-stroke sump-oil change.
Useful service information
Cooling system and flushing
Use the correct flushing cup for the intake beneath the anti-ventilation plate, or a suitable freshwater tank. A generic side-intake earmuff may not seal over this intake. With the propeller removed, establish cooling water before starting, then run in neutral at idle for about five minutes. Monitor water flow, stop the engine before turning off the hose and leave the outboard upright to drain.
Flush after use in salt, muddy or polluted water and rinse salt off the exterior. During pump service, inspect the housing, liner, wear plate, key, gaskets and water-tube connection as well as the impeller.
Gearcase care
Keep the outboard upright and fill through the lower drain hole until lubricant reaches the upper vent, following the instructions for the fitted gearcase. Close the vent before disconnecting the filling pump. Renew the appropriate plug seals and check for leaks. Milky lubricant, free water or larger metal particles need investigation.
Fuel system and spark plugs
Check the fuel valve, hoses and filter for leakage, restriction or deterioration. Replace a contaminated filter and check for leaks after reassembly. Inspect the plug and boot; BP7HS-10 is an alternative specified for this family, with a 1.0 mm gap. Confirm the plug specification against your engine serial.
Propeller, anodes and lubrication
Lubricate the transom clamp screws, tilt and swivel points, throttle/shift pivots and propeller shaft as specified for the engine. Check the reverse-lock mechanism and propeller retaining hardware while servicing.
Inspect anodes regularly, especially in saltwater; replace worn anodes and keep them free of paint, grease and other insulating coatings. With the engine secured against starting, remove the propeller to check for fishing line, seal damage and worn retaining hardware. Grease the specified shaft surfaces before refitting.
Service checks and storage
Before a long period out of use, follow the fuel-stabilising, carburettor-emptying and cylinder-protection procedure for this model. Drain and renew the gear lubricant, protect exposed metal and keep the cooling-system drain passages clear.
A complete service also includes the lanyard stop switch, steering and controls, transom mounting, hoses, accessible fasteners and battery connections where fitted. Check for fuel or gear-oil leaks and normal cooling-water flow after servicing. Keep a record of the work and engine hours.
Need help choosing? Send Boat Service Gold Coast your engine model and serial number, plus a photo of any part or gearcase you are unsure about. We can help match the kit and optional extras before you order.
Use your engine’s serial-specific Mercury manual for complete procedures, tightening specifications and service requirements. Kit pricing covers the listed parts and fluids; workshop labour is separate.